Ad blocker detected: Our website is made possible by displaying online advertisements to our visitors. Please consider supporting us by disabling your ad blocker on our website.
This is the running list of the current Sponsors. Help support TinBoats.net by supporting these guys first if you are shopping for similar products....
I bought this Tohatsu 50/35 about a year ago. Ran it all summer without any issues, took it in to have it serviced/winterized and get a clean bill of...
Last post
If that's the impeller that's been it this summer it honestly doesn't look that bad. Wouldn't hurt to sharpen it but I've seen a lot worse impellers...
Hey everyone. I️ am on the hunt for a good deal on a SS Impeller for my 90/65 Merc. It’s a 7 3/8 C. Prefer 4 blade but will look at 3 blades. New or...
How I'm learning the jet setup: have to add the batteries and trolling motor, have been switching motor trim pin and weight. Added a box of rocks and...
Last post
My 2017 60/40 I removed the stops on my power trim so I can tuck my moter all of the way under you just have to watch and make sure it clears your...
Through break-in and tried out some shallows in the river. Picked up a twig or something and it is making the blower squeak. Trimmed it up and can't...
Last post
Follow advice posted.
FYI there is no reverse thrust on a jet. Water moves through the pump in one direction only.
Bought a mercury 60/40 and it runs great. Only thing is is that I hate having to reach for the ignition and gear shift on the standard tiller handle....
Last post
i bought a new rig in april.it came with bth on the motoer.i gotta say,its super nice and really stout!you would not be disappointd!
Posted in another topic, wasn't sure which to use. Have until Monday to get the facts and make a decision on a good used vee 1648 Weldbilt with 20...
Last post
if you can go for a 60/40 it will perform with a load much better. Don't use a jack plate if your going to leave it as a jet. I run a jack plate but...
Hey guys! Been fishing the heck out of my CC jet. Really enjoying it. We are going to be staying in a house off of the Rappahannock river (Chesapeake...
Last post
Yep, plus when you have a fresh water motor you don't want to corrode it all up in the salt.
I flushed her out and cleaned her up real good. I got...
check this out looks a lot better than my uhmw rockproof boats intake. Probably wouldn't slow a boat down any like the UHMW rockproof one but seems...
Last post
I wouldn't think so aluminum has give in that it will crack or break, I think the urethane has enough give to not break the pump housing. I have one...
Hey fellas. For a while I was about to pull the trigger on a weld-craft with a new 115/80 merc. The longer I put it off the less I could stomach...
Last post
Ok I was just curious about what you were running figured you must have thought about it for a while if you were considering a obj and knew what they...
I've decided to stop wasting time and money trying to improve my Mercury 4S 40 Jet's performance with my boat to a point where I'm satisfied with it...
Last post
I agree with you there about two and four strokes. Those larger yamaha 3 cyl and the omc 3cyl 40-70hp's were some of the best engines I think. The...
I'm confused on which is the correct impeller for my 1995 Evinrude 65/90 1768 Roughneck boat. I believe it is a M73 jet on it. I had a boat mechanic...
Last post
Do you still have this boat and are you interested in selling it?
Morning Gents , I have a 2008 factory Merc 60/40 Jet. Due to job move I now fish different rivers and have quite a bit of run time . Do not actually...
Last post
Something else I forgot about in my first reply. The midsection length is different in the 60 hp prop motors and the factory 60/40 jet. The factory...
I posted this on Mean Chicken, thought I'd post it here too with the number of guys running Jets now.
I have a 2010 Lowe Roughneck 1655D tunnel hull...
Last post
We have had the boat out several times so far, played with weight distribution even more, took the pump apart and found a couple of pieces of junk in...
I have a 2003 Merc 60/40 2 stroke it has lean sneeze issue idles fine and runs wot great only sneezes when slowing down and about 1/4 throttle while...
Last post
Yes i did clean the carbs very well but I think I'm gonna pull them back off again and run them through my ultrasonic cleaner because Im still...
Been looking at 90hp 2 Strokes to replace the 4S 60/40 on my boat. The boat is 16' long, 55 wide and heavy for it's size. Seems like it takes forever...
Last post
I decided to go the easy and less expensive route with a rebuilt 2005 Mercury 90hp 2S from Outboards Unlimited in Astor, Florida. The owner let me...
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot post attachments in this forum
