Search results

used a door entry mat from Lowes,,,,makes for fast easy clean out of the boat

I keep MY pics on MY PC's or hard drive, wouldn't ever give access to the world wide web to my life,,, guess its old school and I like that way,,,,,hate gone to a forum and the pics are gone because they are on some other site and the account is shut down,,, jmo shouldn't be allowed on any...

ill take the 120,,, had 124 yesterday at the Topock AZ house,,,,124 really is not that bad :LOL2: ,,,, dump some water on the shirt and keep going,,, the swamp cooler keeps the house in the high 70s low 80s when it 115 outside when the humidity and dew point are low, electric bill should be less...

Just started making again my old favorite Kodak Kodachrome 64 along with the developer chemicals https://www.amazon.com/gp/offer-listing/B0000520IT/ref=dp_olp_new_mbc?ie=UTF8&condition=new still got my old FTb got in high school, had a F1 I got in 76 and then got a A-1 when they 1st came out...

Nice work!!! 6061 t-6 can be bent, do it all the time,,,not sure what you have equipment and tooling but just takes a larger bend radius, 2 times mat'l thickness ,,,,,,https://www.americanmachinetools.com/bend_radius.htm love them hatches!!! are they lockable??? Just curious what the plan is...

or should be able to match it from the size of your old seal,,,, use to be able to buy the seal saver and seal as a set

took the words right out of my mouth,,,,,,,,have a 80s something 13 ft Fisher myself ,,,,, all depends on the ribs , how many, how their braced, how heavy, full length to and attached to the gunnel and also the size/how strong the gunnel is,,,,, got any pics

Only thing to keep your boat from moving left to right is your tie down straps,, if they are vertical or near vertical and parallel to each other its going to allow the boat to shift sideways at the tailend of the boat,,,, straps need to have a 15 to 20 degree angle on them or more to stop the...

We have welded up a few hundred of them over the years for the boat repair shop next door to our shop,, much like the video Rich posted, we always used wet rags to keep the gear housing cool,,, now they have a heat stop paste that works really really GOOD...

Alweld will build it for you in the catalog or not......

Pull a 2014 G3 1548 VBW behind a 2009 VW TDI (diesel) Jetta that has a 1000lb tow capacity,,,has 25hp etec and a custom built aluminum trailer built by myself ,,, boat motor and trailer is about 650 lbs add TM and batteries gear comes in just about 900 lbs,,,, have no trouble pulling it out of...

Wished I had seen this earlier could of saved you a lot of money and work, a cinch to install, for 5 bucks could have gotten some ''seal savers'',,, they are a thin stainless wear ring that goes over the seal surface of the spendle , realy a good idea to have on any axle new or used, last for...

for not much over a $1500 should be able to get a rebuilt powerhead and not have someone else's problem,, did you look into what was the cause of low compression, could be a easy inexpensive fix ""BOAT"" Bust Out Another Thousand

one option is a umbrella https://www.google.com/search?q=boat+umbrella&biw=1366&bih=676&source=lnms&tbm=isch&sa=X&sqi=2&ved=0ahUKEwis1rbty_fPAhXDjVQKHeBRDKYQ_AUIBygC#imgrc=_ used one for years on my old glass jon in the AZ sun,, sometimes far better then a bimini top,,,, fast and easy to get...

trying to find a used console is one thing trying to find one with the right length cables and the wiring for your needs would be next to impossible,, here is a link that could help you https://www.akmccallumco.com/store-console.htm ,,, know it all adds up but almost better to start out new,,,

welcome to the board yep a west coster probaly a better then 50% chance hes from cali :?: if so need to fill out one of these https://www.dmv.ca.gov/portal/wcm/connect/7885d40d-4d2e-4fc0-b100-3ef8fe562bd7/reg227.pdf?MOD=AJPERES but ya get your profi filled out,,, sure is nice to 1st names and...

yep get it welded,,,, own a weld shop,,,,if ya was to bring it in to our shop to have it welded, would probably charge our minimum charge of $30 if it were all cleaned up and ready to weld,, best to drill a small 3/16 hole on each end of the crack to help stop the crack,,,, do the prep work your...

yep or more and 30 cents a pound for scrap aluminum :cry: ,,,,, ya know still cant see the holes in that pic :? ,,,,,,,,,,, that pic looks even more like a G3 but they all kinda look a like,,back in the day g3 has had to replace a lot of boats because of corroded transoms/hulls from pressure...

me i would weld it up, but I own a weld shop,,a lot would depend where and how easy it is to get too,,,, if you can get to the back side/inside would probably be best to put a patch/ backup on the insyde then weld it from the outside, a 1/2'' hole is not that easy to just fill up with weld...

Ill take a welded boat over a riveted boat any day, I hear people say airplanes are riveted,,, all can say a plane doesn't take the beating a boat does,,, also when is the last time you seen a new riveted ship ,,,, must be a west coaster talk n western, klamath, gregor, have a western and a...