Search results

Bump

Yea I’m still not in it but a little over 500 now and runs amazing! Does well on the Mississippi River for me.

Trying to find a tiller handle setup for a Nissan ns40c 361a-1. Anyone happen to have one or know what will interchange to look on eBay?

Pappy I’m sorry I’ve been mia on this thread. I did finally get around on it and swapped coils around along with known working coils from a motor I purchased. Needed up doing a compression test with a couple other gauges and got the same and even lower. Ended up tearing it down and honing the...

ok pappy! Lets see what you recommend here!? i have now replaced fuel lines, fuel pumps (just because i had them), rebuilt carb, plugs, cleaned ground really good on coil packs and got them good, and fired right up! Then dies. So i finally broke out the compression tester and 70 psi across all...

pappy that was my first thing i tried. used spark tester and top 2 coild wont hit 7/16 gap but very close. but its a weak spark. No3 cylinder will run 7/16 and looks like a 220v welder throwing a 7018 welding rod down a pass. still havent gotten time to compression test yet. also plugs are...

tried idle from 1.5 out to 6 where they were when i got it and no change

Im in it cheap or i wouldnt have gotten it. usually ones i buy cheap turn into parts. this one actually looked decent. got it home and it fired up so going through it

Heck no! for $100 i woulda been a fool not to buy it.

Glad your still here pappy! Yes the oil injection is obsolete. I have also tried 1/4 turn method. Its like anywhere you leave it in the rpms say 1k, or 1500, or 2k itll run there for a sec then die. if you constantly work the throttle it wont do it. Also im running it in a barrel. Going to check...

Recently bought a 2000 johnson 35hp for my personal boat and i now know why they sold it! It will start! Thats about the only good thing. Thought it was the carbs so ordered kits for them and they look like they were just purchased from omc they are so clean. I adjusted the floats, since they...

Had multiple barbed ended connecting different style and sizes of lines. It was like a line had broke and instead of fixing them someone put barbs in place. This was on fuel lines and the primer solenoid lines

Finally got it! Replaced all of the fuel solenoid lines and removed the contraption they had for an internal filter under the hood and fired right up to a bad carb base gasket. Gonna build some new ones tomorrow and should be set to go!

Oh yes. I finally got it lined out. The upper seal and base gasket were shot! Got them replaced and she runs as good as new now

Ok guys, I know someone has had this issue. My friend has an 85 johnson 185. He bought it last year and brought it over today to help him work on it but I'm completely stumped! We put a stator, cdi box, rebuilt carbs, replaced a couple coils that weren't firing, and fuel lines on motor. Motor...

1652 polarkraft 95 evinrude 40hp tiller Custom bowfishing deck, grab bar, and rear tower Modified 1990 astro bass boat trailer

TurboTodd, yes I did remove them again to ensure jetting as you said. They were correct but his bottom 2 carbs were rough! I told him in the beginning and he insisted that i just get it running enough to use as he was debating repowering the boat instead of replacing the carbs on a super low...

Where are you located? I'm I'm west tn and have some 35 parts. If your not too far I can check years and get info on them. Can also ship if need be.

Sorry I'm so late! I finally got it finished! The man is going to end up needing 2 new carbs. They are completely corroded deep into the metal! I did suggest getting all 4 while he was there but only time will tell. However I did get it back to running for him, not the greatest, but it sure runs...

Haha you guessed it. Motorcycles and atvs until about 2007. Started when I was about 8 or 9 building my own lt230 Suzuki and yamaha blaster and took to it like a natural as my father told me. Quit them in high school and started messing with outboards more. But the ole merc tunes have almost...