Search results

Hey guys, just got back into another boat and the motor is a TLDI 40 - 2011 year model. Everything checks out but needs a new tilt/trim motor. Part number below. I have found the Tohatsu part number and I know there are several of these that cross-reference over the brands. Can anyone point...

Reduced!! - $6,999 - Complete Package - Brand New! 404-281-7042 Braselton GA

Im more-so looking for comparison to my 25HP TWO-Cylinder two-stroke. It would just seem, especially with a load, the Honda would do much better.......right?

Appreciate the feedback, how you think power-wise this will compare to my 1996 Evinrude 25 two-stroke? Would it be a worthy upgrade?

I currently have a 1996 Evinrude 25 HP, I am wanting something with 3 cyl and stumbled across this Honda. Honda BF 25 3 cyl four stroke. Any opinions? Seems ya cant really beat a Honda at much....

See below, I am in Braselton GA 404-281-7042 https://atlanta.craigslist.org/atl/boa/4966039142.html

Thanks guys!

I guarantee someone would pay $2,500 that knows about motors. Someone offering $1,200 just doesn't know the value.

Im assuming that is a 3 cyl correct? Id say the $1,200 mark is MUCH too low. A 2007 is pretty **** new still, and is a sought after, 2 stroke with good power and plenty of opps to mod. Id start around $2,500 for motor maybe more.

Got it!

That makes sense Pap, and I do appreciate the shared knowledge from you guys. I think I'll order a tac and check my RPMS before ordering a prop. Actually dead-centering my motor greatly helped with the venting issue. My plan is jack plate/TT (still don't know which one haha) and a SS prop for...

How accurate are those Chinese inductive tacks?

I'll rephrase it some, with the 10x15 the motor did not rev as high and when you put two people in the boat my speed dropped down to like 21-22, which I think is too much and was lugging the motor. That's why I think the 10x13 is perfect, should pull a load a lot better and sounds like it revs...

I'm going to bite the bullet and try out a SS prop. Recently switched form an aluminum 10x15 to a 10x13, didn't lose any top end really and boat is much quicker off the line. I don't have a tach but have a good ear and it sounds like its revving up all the way, and don't think I'd want to rev...

Cost comes into play then ha! What if I got a static Jack Plate and added the Panther T&T. I want some setback if I can.... This leads to me asking, the CMC PT-35 offers setback with T&T, what would be the advantages of going with the Panther?

Update, I moved my motor about 1.5" to the left if your facing rear of boat. The gigantic spray on the right side is gone and almost doesn't vent at all. Gained about 2 MPH even (hit 28-29 today) and caught a 4 lb. spot on Lanier to top it off. So I think now that it's centered correctly And...

Ha yeah I love Lanier, grew up on it in a 23 ft Regal and a couple Sea Doos. I know the lake well and the summers are a mess. The boat is mainly for fishing/hunting but I'm sure will see the lake in the summer. I'll mainly use it to meet people out there and get a couple people on the lake, go...

I'd love an E-Tec as that would be my first choice. But that's out of my budget. A new motor was not even in my thoughts until I stumbled upon the 2007 new in a crate with a warranty for $2,675. If that's not an option, your pretty sure I'd be happier with my 1996 Evinrude?

Yeah I haven't had it that long but have put several hours on it with zero issues. I just like the thought of a new, fuel injected motor with a warranty. Any thoughts on the 2007 EFI's vs the 2015 (Merc 25 HP)??

Thanks 2fast. My seat will stay in the same place and another 4-5" back wont affect me much as it is almost too close right now, so those two wont be issues. Secondly, I want something with some set back (5" or so) to get the motor in cleaner water and be able to run it an inch or two higher...