TinBoats.net
The original aluminum boat site!
Forums
New posts
Search forums
Blog
What's new
New posts
New media
New media comments
Latest activity
Media
New media
New comments
Search media
Members
Current visitors
Log in
Register
What's new
Search
Search
Search titles only
By:
Current visitors
Menu
Log in
Register
Install the app
Install
Forums
Members
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Help Support TinBoats.net:
This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
Pale_Horse_Idaho
Active member
Joined
Mar 13, 2024
Last seen
Apr 20, 2024
Messages
32
Reaction score
27
Find
Find content
Find all content by Pale_Horse_Idaho
Find all threads by Pale_Horse_Idaho
Latest activity
Postings
About
Pale_Horse_Idaho
replied to the thread
Yamaha 25hp 14ft semi-V rpm range question
.
Ive tried going slower but the boat starts to drag in the water near 5000-4800 rpms. Your 60% 3,600rpm's target would be trolling speed...
Apr 20, 2024
Pale_Horse_Idaho
posted the thread
Yamaha 25hp 14ft semi-V rpm range question
in
Motors
.
I tried searching but found 1,200 pages of people arguing over suggested range vs optimal range. Yamaha says 5000-6000 rpm's for my...
Apr 20, 2024
Pale_Horse_Idaho
replied to the thread
77 Smoker-craft Bench Seat Mods
.
Wow super amazing job you did. Way above my pay-grade. When I was re-powering my boat I agonized over Honda vs Yamaha. I ended up with...
Apr 13, 2024
Pale_Horse_Idaho
replied to the thread
Has anyone made a homemade OB motor lift strap to hoist motor onto boat?
.
Those look nice. Maybe 2 of them and wrapped? Any pics of how you wrapped motor? My yamaha has nothing to hold it on front and rear. I...
Apr 9, 2024
Pale_Horse_Idaho
posted the thread
Has anyone made a homemade OB motor lift strap to hoist motor onto boat?
in
Motors
.
If so can I see a picture or design? I looked at the ready made models and they do not inspire confidence.
Apr 9, 2024
Pale_Horse_Idaho
replied to the thread
9.9hp Yamaha...gasping for air?
.
Could be a dozen things........ Clogged carb. Bad fuel pump or hard diaphragm. Bad coil, electrical system that creates spark. Clogged...
Apr 9, 2024
Pale_Horse_Idaho
replied to the thread
Honda BF25 Reverse Shift Issue
.
Have a look at the nut on the shaft going down the back to the gear box. Maybe that nut is out of adjustment or loose. It could be all...
Apr 9, 2024
Pale_Horse_Idaho
replied to the thread
2024 Anything new for laminating a transom?
.
First one I have done, maybe someone with more transoms under their belt can answer that.
Apr 7, 2024
Pale_Horse_Idaho
replied to the thread
POST YOUR PIC'S FISHING GALLERY.......
.
Just a baby we pulled out of the local creek.
Apr 7, 2024
Pale_Horse_Idaho
replied to the thread
2024 Anything new for laminating a transom?
.
A couple snaps of the trim before I install it. Total cost was $130. There are some light tool marks on it I might have to sand out but...
Apr 4, 2024
Pale_Horse_Idaho
replied to the thread
2024 Anything new for laminating a transom?
.
A break from the boat. My new bird dog wanting to kill my chickens.
Apr 3, 2024
Pale_Horse_Idaho
replied to the thread
2024 Anything new for laminating a transom?
.
I measured to old trim cap with a cloth tape measure holding to the surface for the whole measurement. I then had the shop make it 3...
Apr 3, 2024
Pale_Horse_Idaho
replied to the thread
2024 Anything new for laminating a transom?
.
I was going to use a smaller drill but I like your idea better.
Apr 3, 2024
Pale_Horse_Idaho
replied to the thread
2024 Anything new for laminating a transom?
.
OK, made some progress today. Tried to insert transom yesterday and found that the old piece was bowed. The straight piece did NOT want...
Apr 2, 2024
Pale_Horse_Idaho
replied to the thread
Can I get an ASAP opinion??
.
He is right. Look at the direction marks printed on the impeller. Look at the bottom 3 vanes. They point the opposite of the top 3 vanes...
Apr 1, 2024
Loading…
Loading…
Forums
Members
Top