Search results

Hi, The motor is always tuned pretty well, and I didn't really see any change in performance when I changed from the Wally-world stuff. Like I said though, the boat wasn't on the water very often this year. She's sleeping now, so I guess I'll learn more next season. Thanks

Hello all, i ran with biodegradable 2-stroke oil in my 40hp '62 Johnson this year. Pretty crummy weekend weather, so I couldn't form much of an opinion. I really want this to work, as I'm conscious of the impact I'm having on the air and water. I figure I'm scoring a few points for running...

think I'll install passive trim tabs in the spring. Short money compared to any of the powered options. Had'em before, and they worked pretty well. These newer ones have a pin that can lock them flat for when you don't need them quite so badly. Thanks all.

I run a 60's vintage 40hp Johnson on a 14' Arkansas Traveler aluminum double cockpit runabout. The transom is narrow, so there's not much flotation aft. I moved the battery forward to improve the trim, but it still takes a while to get on plane when there are passengers in the rear cockpit. I...

Amen to Rustoleum top coat.

Hi, If the diameter of the wheel has been made significantly smaller, you may find that a slight increase in revs may be necessary.

You can buy the parts to re-hab that venting push-pin mechanism.

Pretty! If there are holes in the area where a windscreen would have been, then I'd look for one to mount there. They're not impossible to find used, and new ones aren't outrageously expensive. The wooden gunnels look rough but they might clean up OK. New stock (white oak is good) wouldn't...

Very cool A candidate for a bright polish job if I ever saw one.

Hi The Turtle Wax spray and wipe stuff is what I have on hand for the cars. It is easy to use, and works well enough on the boat so I haven’t searched for anything else. Wiping down with a beach towel when the boat is first pulled up the ramp helps minimize the water spots.

Here's the MSC part number for 2" solid aluminum brazier head rivets. MSC-67620401 I knew I'd be needing a variety of lengths to restore my boat, (including a new transom) so I bought a box of 2" and cut them to fit. I was able to add a 1/4" aluminum plate to the outside of the transom for...

Hi I replaced a rotted transom and used solid rivets and washers like the originals. I’ll get you the vendor info.

I'm not one for leaving well enough alone. Looks like you could prop the boat on its side and holding a backing iron against the outside, tap those deformations from the inside. Work from the edges toward the deepest part of the dents. I'll bet you can make a considerable improvement.

Thanks! I did use some stripper early on, but found the process pretty nasty. The wire wheel did the removal, and all of the work after that was making finer and finer scratches till shiny. If you can figure out how to use a stripper and not feel like you’re creating an ecological disaster...

I guess there’s more than one way to skin a cat. If I were going to go that route, I’d try to get the boat stood on its end and shimmed “level”. Maybe patch all the places the goop could escape with tape, and do a test fill with a measured volume of water. That’d tell you how much to mix up. I...

Hi, I used a plain old steel wire wheel to remove the old paint I didn't worry about it because I knew there'd be multiple subsequent steps after that. Microscopic rust particles weren't on my radar. I polished everything above the water line using successive grits of sandpaper, then...

Hi again. I'll get a few photos of the completed job on my own CS-14 The plywood does not go all the way down to the bottom and there's an inch or so gap above the hull so as to keep dry when there's some water in the bilge. The new plywood pieces that you'll laminate in place can be slid in...

Hi I've used something very similar to fasten subflooring to steel floor joists. If you inquire at a vendor that deals in steel framing materials, I'd bet you'll find what you need. I've got a few dozen left from when I rebuilt a pontoon boat. Screwed new plywood floor to the beams that...

Hi I have a number of rivets through the transom. There are roves (aluminum washers) on the inside. The rivets through the knee and through the top rail are all through rivets. Blind rivets would interfere with getting the plywood tight to the aluminum. If the holes are larger than the size...