GAS! GAS! GAS!

[FisherofmenNJ]

Hey guys hope all are doing good and the holidays are going well.

I am planning on starting my front casting deck on my 1999 16’ sea nymph hopefully in a few weeks but have a few thoughts to nail down and hope you can help.
Not sure if I should change the current 6gal portable gas tank and put a permanent one under the Casting deck 2/3 of the boat forward. I currently have a 15hp evinrude that does surprisingly well and the tank Is in te stern behind the back seat. It rides well where it’s at but I am planning on being a 25-30hp this year or next and I am thinking when that happens I may wish I had the tank forward to help with weight distribution especially if I have someone else fishing with me. Please share your experiences and opinions! And any pointers on how to do it correctly I know if I’m gonna put it under the deck m gonna have to vent it to prevent fume build up.

 

[airshot]

Having a fuel tank plus a fishing passenger in the front sounds like to much weight forward. You might need to actually experiment with weight estimates while actually on the water to know for sure.

 

[Buster]

With a smallish boat I'm for keeping the fuel tank portable. Easier to grab and fill, easier to drain for winter (if you deal with winter) easier to move around to improve weight distribution. The inconvenience of it taking up precious floor space is real, but outweighed by the benefits of portability. Of course, your analysis may come to a different conclusion.

 

[KMixson]

I have heard that gas repels fish. If you have a permanent tank under the casting deck and spill any fuel on the deck while filling the tank, any bait or lures that you drop on the deck will find that spot.

 

[FuzzyGrub]

My vote would be to keep the 6gal portable tank which will give you flexibility in placement for different varying loads. Depending on our deck plans, in can still be located there as long as the area is well ventilated.

 

[davidj65]

My vote would be to keep the 6gal portable tank which will give you flexibility in placement for different varying loads. Depending on our deck plans, in can still be located there as long as the area is well ventilated.

I was actually looking for something else, and came across this thread. When you built the forward casting deck, did you remove a seat? The back side of it remains open? What did you do for rigidity across the open span? 3/4" plywood?

I am planning on putting a casting deck in this year. I have a bench seat up front and then a hammer bench seat right up against the bow. My thoughts were to use aluminum and lay it over both benches and cover it in the same vinyl that the rest of the boat has. Not sure about 1/16 or 1/8 aluminum, especially if I add a hatch. Weitsmans being around the corner, the alum is not too bad.

 

[FuzzyGrub]

I was actually looking for something else, and came across this thread. When you built the forward casting deck, did you remove a seat? The back side of it remains open? What did you do for rigidity across the open span? 3/4" plywood?

I am planning on putting a casting deck in this year. I have a bench seat up front and then a hammer bench seat right up against the bow. My thoughts were to use aluminum and lay it over both benches and cover it in the same vinyl that the rest of the boat has. Not sure about 1/16 or 1/8 aluminum, especially if I add a hatch. Weitsmans being around the corner, the alum is not too bad.

Yes, I retained the original wood bench seat. It has a sturdy "I" beam structure that makes it plenty strong. You can see the lip of the seat that the hatch seals against. It is 1/2" ext ply. Back of casting deck has an aluminum "L" sandwich under and over it. A single "L" under would have been enough for support. You would want something for top edge protection though. It was tied in to console frame and a sealed 2x6 block on port side. The front of the casting deck has 2x6 blocks for support.

Make sure your boat is stable enough for a high casting deck. Practice by standing on your front bench on your next outing. While this boat was, a 14' Fishmaster I have, was not. Even in this boat, you want to stay mostly near the centerline.

 

[thill]

I was actually looking for something else, and came across this thread. When you built the forward casting deck, did you remove a seat? The back side of it remains open? What did you do for rigidity across the open span? 3/4" plywood?

I am planning on putting a casting deck in this year. I have a bench seat up front and then a hammer bench seat right up against the bow. My thoughts were to use aluminum and lay it over both benches and cover it in the same vinyl that the rest of the boat has. Not sure about 1/16 or 1/8 aluminum, especially if I add a hatch. Weitsmans being around the corner, the alum is not too bad.

I've done this numerous times. It works well. I always put a hatch in there, to access storage. That's the hardest part. This pic was taken before the hatch went in. I used carpet, to dampen sound and make it more comfortable inside. Worked great for quite a few years. I sold the boat last year, and I miss it. My latest boat has a much better ride, but this one was very, very useful and dependable.