Ad blocker detected: Our website is made possible by displaying online advertisements to our visitors. Please consider supporting us by disabling your ad blocker on our website.
This is the running list of the current Sponsors. Help support TinBoats.net by supporting these guys first if you are shopping for similar products....
I bought this 2 tachometer on ebay a couple weeks back. It is just like the standard 3 ones installed on the steering console on most any boat except...
Last post
Perhaps a couple of brackets over the gunnel to hang it, and / or a piece of angle attached between the ribs to support it from below.
I had a friend tell me I have the worst luck with trolling motors. Also said they have a long history of being trouble-free. The warranty repair...
Last post
The two transom mounts came from a local marina - the same place that later reparied/replaced them.
The Edge bow mount was bought on ebay from an out...
I ordered all the parts to install the NMEA 2000 from my Garmin 93V to the Honda 115 yesterday. I was thinking of using the power from the gas gauge...
I’m a little closer to seriously considering adding a trolling motor for the iPilot/co-pilot features. I do a lot of trolling by myself and would use...
Last post
You could easily make a stabilizer I've never used one on my powerdrive v2 which I got used. My powerdrive has stayed outside in not so great indiana...
Does anyone use an under water camera? If so, do you have any comments? I don't ice fish, this would be for open water use. Like everyone, curious...
Last post
I have a GoPro Hero 7 Black. It is waterproof to 10 meters(33 Feet) according to the manual. I used it underwater while snorkeling in Hawaii back in...
It's twice as expensive as some most of the other panels. I need top drawer components on my Weld-craft repower/refurb, it sits uncovered out in the...
Just a thought/
As most fish finders run off 12 volts, where to put the battery can be a challenge, especially if it's a lead/acid type.
Why not just...
Last post
fishfindermounts.com They make all kinds of gadgets for portable fish finder mounts/battery combos.
I'm looking at some trolling motor additions. The first one is the Kipawa replacement blade for my Terrova. The second one is a Ninja Grass Blade or...
I’m gonna use Sternsaver transom mount with epoxy to mount the transducer for Humminbird Helix 5 DI GPS. My prop rotates clockwise so obviously it...
Last post
Well, it seems you really only have two choices. Looking at the rear picture that would be either to the left of the bottom strake or to the right of...
Can someone help with wiring this pane
All of the posts are two wire,in the pics the red center is the on/off switch. 20200106_173746.jpg
Last post
You probably know this already, but make the battery connections last, but not before you check all of the wiring with a meter. I find red and black...
I have a 1973 Lowe 1648 with a 25 etec 2017. It has tilt and trim switch on throttle at console. I fish year round in central Illnois by myself most...
Last post
That's a easy install if you get the switch from Academy get the TH Marine switch. I placed mine on the right rear of my old 45 Mercury Classic 50....
Need some advice with wiring a 12v system. I'll be powering a trolling motor, Fish finder, bilge pump and navigation lights. I want to wire a master...
Last post
The easiest way is a Terminal Mount Fuse Block. Screws right to the battery terminal and has it's own terminal for all of your cables to connect to....
I am converting a 15' aluminum Sea Nymph to a Bass Boat. The plan is to run a 24V trolling motor on the bow and a 12V trolling motor on the stern...
Last post
Several companies make 24v chargers. Noco, Promariner are two brands I've owned, and the Noco was the best fit for me. Price is directly proportional...
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot post attachments in this forum
